Before this change, bisync could only detect changes based on modtime, and
would refuse to run if either path lacked modtime support. This made bisync
unavailable for many of rclone's backends. Additionally, bisync did not account
for the Fs's precision when comparing modtimes, meaning that they could only be
reliably compared within the same side -- not against the opposite side. Size
and checksum (even when available) were ignored completely for deltas.
After this change, bisync now fully supports comparing based on any combination
of size, modtime, and checksum, lifting the prior restriction on backends
without modtime support. The comparison logic considers the backend's
precision, hash types, and other features as appropriate.
The comparison features optionally use a new --compare flag (which takes any
combination of size,modtime,checksum) and even supports some combinations not
otherwise supported in `sync` (like comparing all three at the same time.) By
default (without the --compare flag), bisync inherits the same comparison
options as `sync` (that is: size and modtime by default, unless modified with
flags such as --checksum or --size-only.) If the --compare flag is set, it will
override these defaults.
If --compare includes checksum and both remotes support checksums but have no
hash types in common with each other, checksums will be considered only for
comparisons within the same side (to determine what has changed since the prior
sync), but not for comparisons against the opposite side. If one side supports
checksums and the other does not, checksums will only be considered on the side
that supports them. When comparing with checksum and/or size without modtime,
bisync cannot determine whether a file is newer or older -- only whether it is
changed or unchanged. (If it is changed on both sides, bisync still does the
standard equality-check to avoid declaring a sync conflict unless it absolutely
has to.)
Also included are some new flags to customize the checksum comparison behavior
on backends where hashes are slow or unavailable. --no-slow-hash and
--slow-hash-sync-only allow selectively ignoring checksums on backends such as
local where they are slow. --download-hash allows computing them by downloading
when (and only when) they're otherwise not available. Of course, this option
probably won't be practical with large files, but may be a good option for
syncing small-but-important files with maximum accuracy (for example, a source
code repo on a crypt remote.) An additional advantage over methods like
cryptcheck is that the original file is not required for comparison (for
example, --download-hash can be used to bisync two different crypt remotes with
different passwords.)
Additionally, all of the above are now considered during the final --check-sync
for much-improved accuracy (before this change, it only compared filenames!)
Many other details are explained in the included docs.
Before this change, bisync supported `--backup-dir` only when `Path1` and
`Path2` were different paths on the same remote. With this change, bisync
introduces new `--backup-dir1` and `--backup-dir2` flags to support separate
backup-dirs for `Path1` and `Path2`.
`--backup-dir1` and `--backup-dir2` can use different remotes from each other,
but `--backup-dir1` must use the same remote as `Path1`, and `--backup-dir2`
must use the same remote as `Path2`. Each backup directory must not overlap its
respective bisync Path without being excluded by a filter rule.
The standard `--backup-dir` will also work, if both paths use the same remote
(but note that deleted files from both paths would be mixed together in the
same dir). If either `--backup-dir1` and `--backup-dir2` are set, they will
override `--backup-dir`.
Before this change, bisync had no ability to retry in the event of sync errors.
After this change, bisync will retry if --resilient is passed, but only in one
direction at a time. We can safely retry in one direction because the source is
still intact, even if the dest was left in a messy state. If the first
direction still fails after our final retry, we abort and do NOT continue in
the other direction, to prevent the messy dest from polluting the source. If
the first direction succeeds, we do then allow retries in the other direction.
The number of retries is controllable by --retries (default 3)
bisync: high-level retries if --resilient
Before this change, bisync had no ability to retry in the event of sync errors.
After this change, bisync will retry if --resilient is passed, but only in one
direction at a time. We can safely retry in one direction because the source is
still intact, even if the dest was left in a messy state. If the first
direction still fails after our final retry, we abort and do NOT continue in
the other direction, to prevent the messy dest from polluting the source. If
the first direction succeeds, we do then allow retries in the other direction.
The number of retries is controllable by --retries (default 3)
Before this change, bisync had no mechanism for "retrying" a file again next
time, in the event of an unexpected and possibly temporary error. After this
change, bisync is now essentially able to mark a file as needing to be
rechecked next time. Bisync does this by keeping one prior listing on hand at
all times. In a low-confidence situation, bisync can revert a given file row
back to its state at the end of the last known successful sync, ensuring that
any subsequent changes will be re-noticed on the next run.
This can potentially be helpful for a dynamically changing file system, where
files may be changing quickly while bisync is working with them.
This adds an additional parameter to the creation of each flag. This
specifies one or more flag groups. This **must** be set for global
flags and **must not** be set for local flags.
This causes flags.md to be built with sections to aid comprehension
and it causes the documentation pages for each command (and the
`--help`) to be built showing the flags groups as specified in the
`groups` annotation on the command.
See: https://forum.rclone.org/t/make-docs-for-mortals-not-only-rclone-gurus/39476/
This is possible now that we no longer support go1.12 and brings
rclone into line with standard practices in the Go world.
This also removes errors.New and errors.Errorf from lib/errors and
prefers the stdlib errors package over lib/errors.
