When block is being spread through the network we can get a lot of invs with
the same hash. Some more stale nodes may also announce previous or some
earlier block. We can avoid full DB lookup for them and minimize inv handling
time (timeouts in inv handler had happened in #2744).
It doesn't affect tests, just makes node a little less likely to spend some
considerable amount of time in the inv handler.
Sometimes we already have it, but it's not yet processed, so we can save on
getdata request. It only affects very high-speed networks like 4-1 scenario
and it doesn't affect it a lot, but still we can do it.
This is not exactly the protocol-level batching as was tried in #1770 and
proposed by neo-project/neo#2365, but it's a TCP-level change in that we now
Write() a set of messages and given that Go sets up TCP sockets with
TCP_NODELAY by default this is a substantial change, we have less packets
generated with the same amount of data. It doesn't change anything on properly
connected networks, but the ones with delays benefit from it a lot.
This also improves queueing because we no longer generate 32 messages to
deliver on transaction's GetData, it's just one stream of bytes with 32
messages inside.
Do the same with GetBlocksByIndex, we can have a lot of messages there too.
But don't forget about potential peer DoS attacks, if a peer is to request a
lot of big blocks we need to flush them before we process the whole set.
This allows to naturally scale transaction processing if we have some peer
that is sending a lot of them while others are mostly silent. It also can help
somewhat in the event we have 50 peers that all send transactions. 4+1
scenario benefits a lot from it, while 7+2 slows down a little. Delayed
scenarios don't care.
Surprisingly, this also makes disconnects (#2744) much more rare, 4-node
scenario almost never sees it now. Most probably this is the case where peers
affect each other a lot, single-threaded transaction receiver can be slow
enough to trigger some timeout in getdata handler of its peer (because it
tries to push a number of replies).
We can't make it before 2550000, so move to 2600000. @anatoly-bogatyrev,
please ensure you're using this new height for mainnet NeoFS configurations
next week.
It makes sense in general (further narrowing down the time window when
transactions are processed by consensus thread) and it improves block times a
little too, especially in the 7+2 scenario.
Related to #2744.
Until the consensus process starts for a new block and until it really needs
some transactions we can spare some cycles by not delivering transactions to
it. In tests this doesn't affect TPS, but makes block delays a bit more
stable. Related to #2744, I think it also may cause timeouts during
transaction processing (waiting on the consensus process channel while it does
something dBFT-related).
When the network is big enough, MinPeers may be suboptimal for good network
connectivity, but if we know the network size we can do some estimation on the
number of sufficient peers.
1. UsageText shows the command usage rule. Fixed/added where needed.
2. Description shows the command description, huh. It is shown right after
UsageText, so there's no need to repeat the command usage rule. If
Description contains Example, then it should be printed on a new line.
Usage message is shown on common --help command, thus it should be meaningful
and short. If user needs more detailed command description, then he can use
command-specific help.
As a result, current VM help looks pretty simple:
```
NEO-GO-VM > help
NAME:
VM CLI - Official VM CLI for Neo-Go
USAGE:
[global options] command [command options] [arguments...]
VERSION:
0.99.5-pre-15-g5463ec41
COMMANDS:
exit Exit the VM prompt
ip Show current instruction
break Place a breakpoint
jump Jump to the specified instruction (absolute IP value)
estack Show evaluation stack contents
istack Show invocation stack contents
sslot Show static slot contents
lslot Show local slot contents
aslot Show arguments slot contents
loadnef Load a NEF-consistent script into the VM optionally attaching to it provided signers with scopes
loadbase64 Load a base64-encoded script string into the VM optionally attaching to it provided signers with scopes
loadhex Load a hex-encoded script string into the VM optionally attaching to it provided signers with scopes
loadgo Compile and load a Go file with the manifest into the VM optionally attaching to it provided signers with scopes
loadtx Load transaction into the VM from chain or from parameter context file
loaddeployed Load deployed contract into the VM from chain optionally attaching to it provided signers with scopes
reset Unload compiled script from the VM and reset context to proper (possibly, historic) state
parse Parse provided argument and convert it into other possible formats
run Execute the current loaded script
cont Continue execution of the current loaded script
step Step (n) instruction in the program
stepinto Stepinto instruction to take in the debugger
stepout Stepout instruction to take in the debugger
stepover Stepover instruction to take in the debugger
ops Dump opcodes of the current loaded program
events Dump events emitted by the current loaded program
env Dump state of the chain that is used for VM CLI invocations (use -v for verbose node configuration)
storage Dump storage of the contract with the specified hash, address or ID as is at the current stage of script invocation
changes Dump storage changes as is at the current stage of loaded script invocation
help, h Shows a list of commands or help for one command
GLOBAL OPTIONS:
--help, -h show help
--version, -v print the version
```
Share parameters parsing code between 'contract invokefunction' and
'vm run' commands. It allows VM CLI to parse more complicated parameter
types including arrays and file-backed bytestrings.
