Before this change a server side copy did not preserve the modtime.
This used to work on nextcloud but at some point it started ignoring
the `X-Oc-Mtime` header.
This patch sets the modtime explicitly after a server side copy if the
`X-Oc-Mtime` wasn't accepted.
This problem was discovered in the integration tests.
when multi-thread downloading is enabled, rclone used
to send a write to disk after every read, resulting in a lot
of small writes to different locations of the file.
depending on the underlying filesystem or device, it can be more
efficient to send bigger writes.
Before this change we were incorrectly identifying the root directory
of the listing and adding it into the listing.
This caused higher layers of rclone to emit the error above.
See #7038
Before this change we were incorrectly identifying the root directory
of the listing and adding it into the listing.
This caused higher layers of rclone to emit the error above.
See #7038
Before this change we were incorrectly identifying the root directory
of the listing and adding it into the listing.
This caused higher layers of rclone to emit the error above.
Fixes#7038
This commit
3567a47258 fs: make ConfigString properly reverse suffixed file systems
made fs.ConfigString() return the full config of the backend. Because
mount was using this to make a volume name it started to make volume
names with illegal characters in which couldn't be mounted by macOS.
This fixes the problem by making a separate fs.ConfigStringFull() and
using that where appropriate and leaving the original
fs.ConfigString() function untouched.
Fixes#7063
See: https://forum.rclone.org/t/1-63-beta-fails-to-mount-on-macos-with-on-the-fly-crypt-remote/39090
The SIGUSR2 signal handler for bandwidth limits currently only starts
if rclone is started at a time when a bandwidth limit applies. This
means that if rclone starts _outside_ such a time, i.e. with no
bandwidth limits, then enters a time where bandwidth limits do apply,
it will not be possible to use SIGUSR2 to toggle it.
This fixes that by always starting the signal handler, but only
toggling the limiter if there is a bandwidth limit configured.
Zoho has started returning the results from Range: requests with a 200
response code rather than the technically correct 206 error code.
Before this change this triggered workaround code to deal with Zoho
not obeying Range: requests properly.
This fix tests the returned header for a Content-Range: header and if
it exists assumes it is a valid reply to the Range: request despite
the status being 200.
This problem was spotted by the integration tests.
In 04aa6969a4 we updated the displayed speed to be a rolling
average in core/stats and the progress output but we didn't update the
Prometheus metrics.
This patch updates the Prometheus metrics too.
Fixes#7053
Before this fix, if the upload failed for some reason the yandex
backend would attempt to retry itself it which would fail immediately
with 400 Bad Request.
Normally we retry uploads at a higher level so they can be done with
new data and this patch does that.
See #7044
Before this change if doing a recursive directory listing with
`--files-from` if more than `--checkers` files errored (other than
file not found) then rclone would deadlock.
This fixes the problem by exiting on the first error.
Before this change partially uploaded files (when --inplace is not in
effect) would be left lying around in the file system if rclone was
killed in the middle of a transfer.
This adds an exit handler to remove the file and removes it when the
file is complete.
Before this change, some parts of operations called the Open method on
objects directly, and some called NewReOpen to make an object which
can re-open itself on errors.
This adds a new function operations.Open which should be called
instead of fs.Object.Open to open a reliable stream of data and
changes all call sites to use that.
This means `rclone check --download` and `rclone cat` will re-open
files on failures.
See: https://forum.rclone.org/t/does-rclone-support-retries-for-check-when-using-download-flag/38641
Before this change we tested special errors for straight equality.
This works for all normal backends, but the union backend may return
wrapped errors which contain the special error types.
In particular if a pcloud backend was part of a union when attempting
to set modification times the fs.ErrorCantSetModTime return wasn't
understood because it was wrapped in a union.Error.
This fixes the problem by using errors.Is instead in all the
comparisons in operations.
See: https://forum.rclone.org/t/failed-to-set-modification-time-1-error-pcloud-cant-set-modified-time/38596
Before this change the Errors type in the union backend produced
errors which could not be Unwrapped to test their type.
This adds the (go1.20) Unwrap method to the Errors type which allows
errors.Is to work on these errors.
It also adds unit tests for the Errors type and fixes a couple of
minor bugs thrown up in the process.
See: https://forum.rclone.org/t/failed-to-set-modification-time-1-error-pcloud-cant-set-modified-time/38596
Before this fix we used the bin/get-github-release.go script to
install nfpm.
However this script fails scraping the downloads page when the target
has more than a few download options. The alternative would be using
the GitHub API but this needs authentication so as not to be rate
limited on GitHub actions.
This patch switches over to go install which is less efficient but
should work in all circumstances.
