And include some node-specific configurations there with backwards
compatibility. Note that in the future we'll remove Ledger's
fields from the ProtocolConfiguration and it'll be possible to access them in
Blockchain directly (not via .Ledger).
The other option tried was using two configuration types separately, but that
incurs more changes to the codebase, single structure that behaves almost like
the old one is better for backwards compatibility.
Fixes#2676.
* treat connected/handshaked peers separately in the discoverer, save
"original" address for connected ones, it can be a name instead of IP and
it's important to keep it to avoid reconnections
* store name->IP mapping for seeds if and when they're connected to avoid
reconnections
* block seed if it's detected to be our own node (which is often the case for
small private networks)
* add an event for handshaked peers in the server, connected but
non-handshaked ones are not really helpful for MinPeers or GetAddr logic
Fixes#2796.
This is not exactly the protocol-level batching as was tried in #1770 and
proposed by neo-project/neo#2365, but it's a TCP-level change in that we now
Write() a set of messages and given that Go sets up TCP sockets with
TCP_NODELAY by default this is a substantial change, we have less packets
generated with the same amount of data. It doesn't change anything on properly
connected networks, but the ones with delays benefit from it a lot.
This also improves queueing because we no longer generate 32 messages to
deliver on transaction's GetData, it's just one stream of bytes with 32
messages inside.
Do the same with GetBlocksByIndex, we can have a lot of messages there too.
But don't forget about potential peer DoS attacks, if a peer is to request a
lot of big blocks we need to flush them before we process the whole set.
When the network is big enough, MinPeers may be suboptimal for good network
connectivity, but if we know the network size we can do some estimation on the
number of sufficient peers.
They can fail right in the getPeers or they can fail later when packet send
is attempted. Of course they can complete handshake in-between these events,
but most likely they won't and we'll waste more resources on this attempt. So
rule out bad peers immediately.
Drop EnqueueP2PPacket, replace EnqueueHPPacket with EnqueueHPMessage. We use
Enqueue* when we have a specific per-peer message, it makes zero sense
duplicating serialization code for it (unlike Broadcast*).
Follow the general rules of broadcasts, even though it's somewhat different
from Inv, we just want to get some reply from our neighbors to see if we're
behind. We don't strictly need all neighbors for it.
We have a number of queues for different purposes:
* regular broadcast queue
* direct p2p queue
* high-priority queue
And two basic egress scenarios:
* direct p2p messages (replies to requests in Server's handle* methods)
* broadcasted messages
Low priority broadcasted messages:
* transaction inventories
* block inventories
* notary inventories
* non-consensus extensibles
High-priority broadcasted messages:
* consensus extensibles
* getdata transaction requests from consensus process
* getaddr requests
P2P messages are a bit more complicated, most of the time they use p2p queue,
but extensible message requests/replies use HP queue.
Server's handle* code is run from Peer's handleIncoming, every peer has this
thread that handles incoming messages. When working with the peer it's
important to reply to requests and blocking this thread until we send (queue)
a reply is fine, if the peer is slow we just won't get anything new from
it. The queue used is irrelevant wrt this issue.
Broadcasted messages are radically different, we want them to be delivered to
many peers, but we don't care about specific ones. If it's delivered to 2/3 of
the peers we're fine, if it's delivered to more of them --- it's not an
issue. But doing this fairly is not an easy thing, current code tries performing
unblocked sends and if this doesn't yield enough results it then blocks (but
has a timeout, we can't wait indefinitely). But it does so in sequential
manner, once the peer is chosen the code will wait for it (and only it) until
timeout happens.
What can be done instead is an attempt to push the message to all of the peers
simultaneously (or close to that). If they all deliver --- OK, if some block
and wait then we can wait until _any_ of them pushes the message through (or
global timeout happens, we still can't wait forever). If we have enough
deliveries then we can cancel pending ones and it's again not an error if
these canceled threads still do their job.
This makes the system more dynamic and adds some substantial processing
overhead, but it's a networking code, any of this overhead is much lower than
the actual packet delivery time. It also allows to spread the load more
fairly, if there is any spare queue it'll get the packet and release the
broadcaster. On the next broadcast iteration another peer is more likely to be
chosen just because it didn't get a message previously (and had some time to
deliver already queued messages).
It works perfectly in tests, with optimal networking conditions we have much
better block times and TPS increases by 5-25%% depending on the scenario.
I'd go as far as to say that it fixes the original problem of #2678, because
in this particular scenario we have empty queues in ~100% of the cases and
this new logic will likely lead to 100% fan out in this case (cancelation just
won't happen fast enough). But when the load grows and there is some waiting
in the queue it will optimize out the slowest links.
1. Initialization is performed via `Blockchain` methods.
2. Native Oracle contract updates list of oracle nodes
and in-fly requests in `PostPersist`.
3. RPC uses Oracle module directly.
Right now a single slow peer can slow down whole network.
Do broadcast in 2 parts:
1. Perform non-blocking send to all peers if possible.
2. Perform blocking sends until message is sent to 2/3 of good peers.
Prices are defined in as a coefficients to `BaseExecFee` which
is defined by Policy contract (TBD later).
Native method prices are defined without need to multiply.
Now we have VerifyTx() and PoolTx() APIs that either verify transaction in
isolation or verify it against the mempool (either the primary one or the one
given) and then add it there. There is no possibility to check against the
mempool, but not add a transaction to it, but I doubt we really need it.
It allows to remove some duplication between old PoolTx and verifyTx where
they both tried to check transaction against mempool (verifying first and then
adding it). It also saves us utility token balance check because it's done by
the mempool anyway and we no longer need to do that explicitly in verifyTx.
It makes AddBlock() and verifyBlock() transaction's checks more correct,
because previously they could miss that even though sender S has enough
balance to pay for A, B or C, he can't pay for all of them.
Caveats:
* consensus is running concurrently to other processes, so things could
change while verifyBlock() is iterating over transactions, this will be
mitigated in subsequent commits
Improves TPS value for single node by at least 11%.
Fixes#667, fixes#668.
Turns out, C# node no longer broadcasts an Inv when it's creating a block,
instead it sends a ping and if we're not paying attention to the height
specified there we're technically missing a new block. Of course we'll get it
later after ping timer expiration and regular ping/pong sequence, but that's
delaying it for no good reason.
It no longer depends on blockchain state and there can't ever be an error, in
fact we can always iterate over signers, so copying these hashes doesn't make
much sense at all as well as sorting arrays in verifyTxWitnesses (witnesses
order must match signers order).
