It is used a lot in clients (including our benchmark).
`Uint160` is already optimized.
```
name old time/op new time/op delta
Uint256DecodeStringLE-8 150ns ±15% 112ns ± 3% -25.23% (p=0.000 n=10+10)
name old alloc/op new alloc/op delta
Uint256DecodeStringLE-8 96.0B ± 0% 64.0B ± 0% -33.33% (p=0.000 n=10+10)
name old allocs/op new allocs/op delta
Uint256DecodeStringLE-8 2.00 ± 0% 1.00 ± 0% -50.00% (p=0.000 n=10+10)
```
Signed-off-by: Evgeniy Stratonikov <evgeniy@nspcc.ru>
We're using batches in wrong way during persist, we already have all changes
accumulated in two maps and then we move them to batch and then this is
applied. For some DBs like BoltDB this batch is just another MemoryStore, so
we essentially just shuffle the changeset from one map to another, for others
like LevelDB batch is just a serialized set of KV pairs, it doesn't help much
on subsequent PutBatch, we just duplicate the changeset again.
So introduce PutChangeSet that allows to take two maps with sets and deletes
directly. It also allows to simplify MemCachedStore logic.
neo-bench for single node with 10 workers, LevelDB:
Reference:
RPS 30189.132 30556.448 30390.482 ≈ 30379 ± 0.61%
TPS 29427.344 29418.687 29434.273 ≈ 29427 ± 0.03%
CPU % 33.304 27.179 33.860 ≈ 31.45 ± 11.79%
Mem MB 800.677 798.389 715.042 ≈ 771 ± 6.33%
Patched:
RPS 30264.326 30386.364 30166.231 ≈ 30272 ± 0.36% ⇅
TPS 29444.673 29407.440 29452.478 ≈ 29435 ± 0.08% ⇅
CPU % 34.012 32.597 33.467 ≈ 33.36 ± 2.14% ⇅
Mem MB 549.126 523.656 517.684 ≈ 530 ± 3.15% ↓ 31.26%
BoltDB:
Reference:
RPS 31937.647 31551.684 31850.408 ≈ 31780 ± 0.64%
TPS 31292.049 30368.368 31307.724 ≈ 30989 ± 1.74%
CPU % 33.792 22.339 35.887 ≈ 30.67 ± 23.78%
Mem MB 1271.687 1254.472 1215.639 ≈ 1247 ± 2.30%
Patched:
RPS 31746.818 30859.485 31689.761 ≈ 31432 ± 1.58% ⇅
TPS 31271.499 30340.726 30342.568 ≈ 30652 ± 1.75% ⇅
CPU % 34.611 34.414 31.553 ≈ 33.53 ± 5.11% ⇅
Mem MB 1262.960 1231.389 1335.569 ≈ 1277 ± 4.18% ⇅
VM always has istack and it doesn't even change, so doing this microallocation
makes no sense. Notice that estack is a bit harder to change we do replace it
in some cases and we compare pointers to it as well.
It requires only two methods from Blockchainer: AddBlock and
BlockHeight. New interface will allow to easily reuse the block queue
for state exchange purposes.
Do not allocate a separate buffer for the transfer.
```
name old time/op new time/op delta
NEP17TransferLog_Append-8 58.8µs ± 3% 32.1µs ± 1% -45.40% (p=0.000 n=10+9)
name old alloc/op new alloc/op delta
NEP17TransferLog_Append-8 118kB ± 1% 44kB ± 3% -63.00% (p=0.000 n=9+10)
name old allocs/op new allocs/op delta
NEP17TransferLog_Append-8 901 ± 1% 513 ± 3% -43.08% (p=0.000 n=9+8)
```
Signed-off-by: Evgeniy Stratonikov <evgeniy@nspcc.ru>
Refactor code and be fine with sending to just 2/3 of proper peers. Previously
it was an edge case, but it can be a normal thing to do also as broadcasting
to everyone is obviously too expensive and excessive (hi, #608).
Baseline (four node, 10 workers):
RPS 8180.760 8137.822 7858.358 7820.011 8051.076 ≈ 8010 ± 2.04%
TPS 7819.831 7521.172 7519.023 7242.965 7426.000 ≈ 7506 ± 2.78%
CPU % 41.983 38.775 40.606 39.375 35.537 ≈ 39.3 ± 6.15%
Mem MB 2947.189 2743.658 2896.688 2813.276 2863.108 ≈ 2853 ± 2.74%
Patched:
RPS 9714.567 9676.102 9358.609 9371.408 9301.372 ≈ 9484 ± 2.05% ↑ 18.40%
TPS 8809.796 8796.854 8534.754 8661.158 8426.162 ≈ 8646 ± 1.92% ↑ 15.19%
CPU % 44.980 45.018 33.640 29.645 43.830 ≈ 39.4 ± 18.41% ↑ 0.25%
Mem MB 2989.078 2976.577 2306.185 2351.929 2910.479 ≈ 2707 ± 12.80% ↓ 5.12%
There is a nuance with this patch however. While typically it works the way
outlined above, sometimes it works like this:
RPS ≈ 6734.368
TPS ≈ 6299.332
CPU ≈ 25.552%
Mem ≈ 2706.046MB
And that's because the log looks like this:
DeltaTime, TransactionsCount, TPS
5014, 44212, 8817.710
5163, 49690, 9624.249
5166, 49523, 9586.334
5189, 49693, 9576.604
5198, 49339, 9491.920
5147, 49559, 9628.716
5192, 49680, 9568.567
5163, 49750, 9635.871
5183, 49189, 9490.450
5159, 49653, 9624.540
5167, 47945, 9279.079
5179, 2051, 396.022
5015, 4, 0.798
5004, 0, 0.000
5003, 0, 0.000
5003, 0, 0.000
5003, 0, 0.000
5003, 0, 0.000
5004, 0, 0.000
5003, 2925, 584.649
5040, 49099, 9741.865
5161, 49718, 9633.404
5170, 49228, 9521.857
5179, 49773, 9610.543
5167, 47253, 9145.152
5202, 49788, 9570.934
5177, 47704, 9214.603
5209, 46610, 8947.975
5249, 49156, 9364.831
5163, 18284, 3541.352
5072, 174, 34.306
On a network with 4 CNs and 1 RPC node there is 1/256 probability that a block
won't be broadcasted to RPC node, so it won't see it until ping timeout kicks
in. While it doesn't see a block it can't accept new incoming transactions so
the bench gets stuck basically. To me that's an acceptable trade-off because
normal networks are much larger than that and the effect of this patch is way
more important there, but still that's what we have and we need to take into
account.
send() can return errStateMismatch, errGone and errBusy. errGone means the
peer is dead and it won't ever be active again, it doesn't make sense retrying
sends to it. errStateMismatch is technically "not yet ready", but we can't
wait for it either, no one knows how much will it take to complete
handshake. So only errBusy means we can retry.
So keep track of dead peers and adjust tries counting appropriately.
It doesn't change much, we can't magically get more valid peers and if some
die while we're iterating we'd detect that by an error returned from send().
